Search found 19 matches

by champcsm
Fri Jun 17, 2016 4:54 pm
Forum: AMIE NBCAFE
Topic: Tips to pass Material Science in one attempt
Replies: 12
Views: 329922

Re: Tips to pass Material Science in one attempt

study Any reference book,make notes & note all equations ..
c/s old question paper ..
B confident write in your own language ..
luk @ qp read carefully decide questions & luk @ wrist watch timing too.
End result will b passing ..
by champcsm
Fri Jun 17, 2016 4:44 pm
Forum: Fundamental of Design and Manufacturing (AD 301))
Topic: Hooke’s Law
Replies: 0
Views: 1286

Hooke’s Law

Hooke’s Law in 1D Once the values of E, ν, G and α are experimentally determined (for widely used structural materials they can be simply read off a manual), they can be used to construct thermoelastic constitutive equations that link stresses and strains as described in the following subsections. §...
by champcsm
Fri Jun 17, 2016 4:40 pm
Forum: Fundamental of Design and Manufacturing (AD 301))
Topic: HEAT CONDUCTION
Replies: 0
Views: 1459

HEAT CONDUCTION

HEAT CONDUCTION 1.1 Introduction Heat conduction is one of the three basic modes of thermal energy transport (convection and radiation being the other two) and is involved in virtually all process heat-transfer operations. In commercial heat exchange equipment, for example, heat is conducted through...
by champcsm
Fri Jun 17, 2016 4:36 pm
Forum: Fundamental of Design and Manufacturing (AD 301))
Topic: NON CONVENTIONAL ENERGY SYSTEMS -syllbus
Replies: 0
Views: 1281

NON CONVENTIONAL ENERGY SYSTEMS -syllbus

NON CONVENTIONAL ENERGY SYSTEMS Group A Introduction to non-conventional sources—Solar, bio-gas, wind, tidal, geothermal. Basic bio-conversion mechanism; source of waste; simple digester; composition and calorific values of bio-gas. Wind and tidal energy generation; Special characteristics; Turbine ...
by champcsm
Fri Jun 17, 2016 4:36 pm
Forum: Fundamental of Design and Manufacturing (AD 301))
Topic: INTERNAL COMBUSTION ENGINES -syllbus
Replies: 0
Views: 1193

INTERNAL COMBUSTION ENGINES -syllbus

INTERNAL COMBUSTION ENGINES Group A Classification of engines according to fuels, cycle of operation and number of strokes, construction details, value arrangements, application of IC engines, review of air standard cycles, deviation of actual cycles from fuel-air cycles, various influencing factors...
by champcsm
Fri Jun 17, 2016 4:35 pm
Forum: Fundamental of Design and Manufacturing (AD 301))
Topic: TURBOMACHINERY -syllbus
Replies: 0
Views: 1203

TURBOMACHINERY -syllbus

TURBOMACHINERY Group A Positive displacement and turbo machines. Basic principles of rotodynamic machines. Efficiency of turbo machines. Flow through nozzles and blade passages: Steady flow through nozzles, isentropic flow; Effect of friction in flow passages; Converging-diverging nozzles; Flow of w...
by champcsm
Fri Jun 17, 2016 4:34 pm
Forum: Fundamental of Design and Manufacturing (AD 301))
Topic: COMPUTER AIDED MANUFACTURING -syllbus
Replies: 0
Views: 1140

COMPUTER AIDED MANUFACTURING -syllbus

COMPUTER AIDED MANUFACTURING Group A Basic definitions of manufacturing systems: Definitions, design, planning and control. Part design and CAD: Engineering design, design drafting and its interpretation, inspection and measurement. A brief history of CAD, CAD hardware and software. Fundamentals of ...
by champcsm
Fri Jun 17, 2016 4:33 pm
Forum: Fundamental of Design and Manufacturing (AD 301))
Topic: TOOL AND DIE DESIGN -syllbus
Replies: 0
Views: 1443

TOOL AND DIE DESIGN -syllbus

TOOL AND DIE DESIGN Group A Influence of tools and dies on quality, productivity and environment, tool design methods and procedures, tool making practices, tooling materials and treatment. Jigs and fixtures. Basic principles of locating and clamping, development of fixture using locating, clamping,...
by champcsm
Fri Jun 17, 2016 4:33 pm
Forum: Fundamental of Design and Manufacturing (AD 301))
Topic: MANUFACTURING SCIENCE -syllbus
Replies: 0
Views: 977

MANUFACTURING SCIENCE -syllbus

MANUFACTURING SCIENCE Group A Deformation of metals, stress-strain curves, temperature and strain rate effects, ductility and toughness, plane-strain deformation, mechanism of plastic deformation, control of material properties—alloying and heat treatment. Sand casting: Pattern materials and allowan...
by champcsm
Fri Jun 17, 2016 4:32 pm
Forum: Fundamental of Design and Manufacturing (AD 301))
Topic: COMPUTER AIDED ENGINEERING DESIGN -syllbus
Replies: 0
Views: 999

COMPUTER AIDED ENGINEERING DESIGN -syllbus

COMPUTER AIDED ENGINEERING DESIGN Group A Computer aided design of engineering systems. Applications in modelling, analysis, design and manufacturing. Computer graphics, raster graphics and interactiveness, pixels and graphic display in computers, windows and view-ports, lines and circles, graphic d...

Go to advanced search